Meyer Sound ULTRA-X40
-
Code:143
-
Weight:0.000 Kgs
Meyer Sound ULTRA-X40 Wide Coverage Loudspeaker
SPECIFICATIONS
|
ACOUSTICAL1 |
ULTRA-X40 |
ULTRA-X42 |
Operating Frequency Range2 Frequency Response3 Phase Response Maximum SPL4
Low Frequency High Frequency
Type Maximum Common Mode Range
Input Impedance
Nominal Input Sensitivity
Type
Total Output Power7
THD, IM, TIM
Cooling
Connector Automatic Voltage Selection Safety Rated Voltage Range Turn-on and Turn-off Points
55 Hz – 19.5 kHz
56 Hz – 19 kHz ± 4 dB
90 Hz – 19.5 kHz ±45° 138 dB
Rotatable horn: 110° x 50°
Two 8-inch cone drivers; 4 Ω nominal impedance
55 Hz – 19.5 kHz
58 Hz – 18 kHz ± 4 dB
90 Hz – 19.5 kHz ±45° 140 dB
Rotatable horn: 70° x 50°
|
Linear Peak SPL5 |
132.5 dB with 18 dB crest factor (M-noise), 130 dB (Pink Noise), 131 dB (B-noise) |
134 dB with 18.5 dB crest factor (M-noise), 132 dB (Pink Noise), 134 dB (B-noise) |
|
COVERAGE |
||
TRANSDUCERS
AUDIO INPUT
One 3-inch diaphragm compression driver connected to a rotatable horn; 8 Ω nominal impedance Differential, electronically balanced
±15 V DC, clamped to earth for voltage transient protection
10 kΩ differential between pins 2 and 3
0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music
three-channel, Class-D
1950 W peak
<0.02%
Convection
powerCON 20 input with loop output
90–265 V AC, 50–60 Hz
100–240 V AC, 50–60 Hz
90 V AC turn-on, no turn-off; internal fuse protection above 265 V AC
0.27 A rms (115 V AC); 0.25 A rms (230 V AC); 0.29 A rms (100 V AC)
1.9 A rms (115 V AC); 1.0 A rms (230 V AC); 2.2 A rms (100 V AC)
3.1 A rms (115 V AC); 1.5 A rms (230 V AC); 3.4 A rms (100 V AC)
6.9 A peak (115 V AC); 3.4 A peak (230 V AC); 7.9 A peak (100 V AC)
<20 A peak
|
Connectors |
XLR 3-pin female input with male loop output; optional XLR 5-pin connector to accommodate both balanced audio and RMS signals. |
|
Wiring6 |
Pin 1: Chassis/earth through 1 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies Pin 2: Signal + |
|
Input Level |
Audio source must be capable of producing of +20 dBV (10 V rms) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker. |
|
AMPLIFIER |
|
AC POWER
CURRENT DRAW
Idle Current Maximum Long-Term Continuous Current (>10 sec) Burst Current (<1 sec)8 Maximum Instantaneous Peak Current Inrush Current
SPECIFICATIONS, CONT’D.
RMS NETWORK (OPTIONAL) PHYSICAL
NOTES
Dimensions Weight Enclosure Protective Grille
Rigging
Two-conductor twisted-pair network that reports all operating parameters of amplifiers to system operator’s host computer.
W: 12.51 in (318 mm) x H: 22.31 in (567 mm) x D: 14 in (356 mm); D with handles: 15.38 in (391 mm)
52 lb (23.6 kg)
Premium multi-ply birch with slightly textured black finish
Powder-coated, round-perforated steel
11 integrated M8 threaded points; 35 mm Pole Mount with M20 thread; optional accessories for various rigging options (see accessories section).
